收藏本站
SX1211
WIRELESS & SENSING
Note for mass production: The VCO capacitance is piece to piece dependant. As such, the optimization proposed
above should be verified on several prototypes, to ensure that the population is centered on 100 mV.
3.2.6. PLL Loop Filter
To adequately reject spurious components arising from the comparison frequency Fcomp, an external 2 nd order
loop filter is employed.
RL1
LF_M
CL2
CL1
LF_P
Figure 7: Loop Filter
Following the recommendations made in section 3.2.4, the loop filter proposed in the reference design’s bill of
material on section 7.5.3 should be used. The loop filter settings are frequency band independent and are hence
relevant to all implementations of the SX1211.
3.2.7. PLL Lock Detection Indicator
The SX1211 also features a PLL lock detect indicator. This is useful for optimizing power consumption, by adjusting
the synthesizer wake up time (TS_FS), since the PLL startup time is lower than specified under nominal conditions.
The lock status can be read on bit IRQParam_PLL_lock, and must be cleared by writing a “1” to this same register.
In addition, the lock status can be reflected in pin 23 PLL_LOCK, by setting the bit IRQParam_Enable_lock_detect.
3.2.8. Frequency Calculation
As shown in Figure 5 the PLL structure comprises three different dividers, R, P and S, which set the output
frequency through the LO. A second set of dividers is also available to allow rapid switching between a pair of
frequencies: R1/P1/S1 and R2/P2/S2. These six dividers are programmed by six bytes of the register MCParam
from addresses 6 to 11.
3.2.8.1. FSK Mode
The following formula gives the relationship between the local oscillator, and R, P and S values, when using FSK
modulation.
Frf , fsk =
9
8
Flo
Frf , fsk =
9 Fxtal
8 R + 1
[ 75 ( P + 1 ) + S ) ]
3.2.8.2. OOK Mode
Due to the manner in which the baseband OOK symbols are generated, the signal is always offset by the FSK
frequency deviation (Fdev - as programmed in MCParam_Freq_dev). Hence, the center of the transmitted OOK
signal is:
Rev 8 – February 2013
Page 16 of 92
www.semtech.com
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SX1223SK868 KIT STARTER FOR XE1223 868MHZ
SX1231-31SKB915 TVS
SX1240SKA433 TVS
SX1701BI085TRT IC AMP 2.5GHZ 5.3V 16-MLPQ
TA002-10002 LED HEATSINK W/FAN 12V 40X10MM
TC620HEPA IC TEMP SNSR 5V DUAL TRIP 8-DIP
TC623CVOA713 IC TEMP SNSR 3V DUAL TRIP 8-SOIC
TC624VOA IC TEMP SNSR PROG 2.7V 8SOIC
相关代理商/技术参数
SX1212 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Ultra-Low Power Integrated 300-510MHz Transceiver
SX1212-11SKA433 制造商:Semtech Corporation 功能描述:SX1212 433Mhz USB Kit With 2 SX1212-01SKA433SMA, Antenna Connector, RS232 Cable
SX1212-12SKA433 制造商:Semtech Corporation 功能描述:2 X SX1212SKA 制造商:Semtech Corporation 功能描述:Deluxe USB Starter Kit for SX1212, Includes Two USB Interface Boards at 433MHz 制造商:Semtech 功能描述:2 X SX1212SKA
SX1212-DK7A433 制造商:Semtech Corporation 功能描述:Evaluation Board for SX1212 Transceiver
SX1212IWLTRT 功能描述:IC TXRX 300MHZ-510MHZ 32-TQFN RoHS:是 类别:RF/IF 和 RFID >> RF 收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:30 系列:- 频率:4.9GHz ~ 5.9GHz 数据传输率 - 最大:54Mbps 调制或协议:* 应用:* 功率 - 输出:-3dBm 灵敏度:- 电源电压:2.7 V ~ 3.6 V 电流 - 接收:* 电流 - 传输:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 工作温度:-25°C ~ 85°C 封装/外壳:68-TQFN 裸露焊盘 包装:管件
SX1213 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Ultra-Low Power Integrated UHF Receiver
SX1213IWLTRT 制造商:Semtech Corporation 功能描述: 制造商:Semtech Corporation 功能描述:SX1213 Series 510 MHz 200 Kbps Ultra-Low Power Integrated UHF Receiver - TQFN-32
SX1223 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:425 - 475 MHz / 850 - 950 MHz Integrated UHF Transmitter